4g61t.org http://www.4g61t.org/forum/ |
|
New Member, Old Colt! Take a look :) http://www.4g61t.org/forum/viewtopic.php?f=9&t=36966 |
Page 3 of 3 |
Author: | coltdriver92 [ Tue Nov 13, 2012 6:15 am ] |
Post subject: | Re: New Member, Old Colt! Take a look :) |
You guys are going to confuse him. Here you go. Shocks and struts from tire rack. http://www.tirerack.com/suspension/Susp ... toModClar= B&G springs http://www.raceinspired.com/cs-21-springs.aspx I would also go forth and replace the top hats on the front and back and get new bump stops and dust boot covers. |
Author: | ZachSorensen [ Sat Mar 09, 2013 4:43 pm ] |
Post subject: | Re: New Member, Old Colt! Take a look :) |
Sooooooo.... Haven't done anything lately, besides replace the front crank seal and timing belt. It runs okay, other than the fact that it has a very hard time starting in the cold in the morning. It also seems to be running slower than before, or maybe I'm just noticing the 92hp now. xD. It took me some 8-10 seconds to get from 50-60 up a small slanted hill.. hmm. Anywho, I guess this is where I spit out my ideas of what I'm planning to do if it's possible for me, budget/knowledge wise.
If anyone has comments, advice, whatever let me know. I'd appreciate it all, thanks! -Zach |
Author: | 89Mirageman [ Fri Aug 02, 2013 9:49 am ] |
Post subject: | Re: New Member, Old Colt! Take a look :) |
Looks awesome! Brings back memories of my 1st csm. |
Author: | ZachSorensen [ Fri Aug 02, 2013 10:05 am ] |
Post subject: | Re: New Member, Old Colt! Take a look :) |
Thanks! btw yours looked amazing. If only I could get smart enough to do the swap soon lol. |
Author: | mirage760 [ Mon Aug 05, 2013 1:28 pm ] |
Post subject: | Re: New Member, Old Colt! Take a look :) |
that looks good |
Author: | Flying Eagle [ Mon Aug 05, 2013 10:46 pm ] |
Post subject: | Re: New Member, Old Colt! Take a look :) |
You don't want to convert everything to 5 lug. You want to install, at a minimum, the turbo sized brakes 266mm and pads, or the Elantra front brakes 258mm and pads. Don't worry about going to twin piston brakes, as you don't have enough umph behind the engine to warrant that yet. You will need: better booster, 4:1 ratio turbo Colt/Mirage or 92-95 Elantra and re-use the spacer plate from the Colt/Mirage turbo front brake calipers/brackets/pads/pad shims for bracket mounting and backing shim plates turbo rear brakes calipers/brackets/pads/pad shims for bracket mounting and backing shim plates turbo parking brake cables eliminate the residual valve in the rear brake setup (if you have drums installed currently) fabricate a left and right side bracket to hold the brake hard lines on the rear axle brake booster hose with proper check valve - editted Aug 2014 http://www.amayama.com/search/?q=MB277029 This is the check valve as searched for the C53a Cyborg 1.6T turbo proportioning valve turbo master cylinder 7/8" with proper line arrangement - may match your lines at the moment and may not -I have not done the swap in this regard yet Food for thought. Quote: Bigger breaks/5 Lug (Gotta look through the archives and figure out what I need)
Also find out why the engine is lacking so much power, because if something is about to go wrong, money spent on the brakes will be absolutely the wrong way to go.
|
Author: | Mechacode [ Tue Aug 06, 2013 3:42 pm ] |
Post subject: | Re: New Member, Old Colt! Take a look :) |
Kinda looks like an undercover cop car. |
Page 3 of 3 | All times are UTC-05:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |