This turned out very nicely. It was a lot of fun saturday night.
| 4g61t.org http://www.4g61t.org/forum/ |
|
| Friday Night Projects: Exhaust http://www.4g61t.org/forum/viewtopic.php?f=9&t=28637 |
Page 1 of 1 |
| Author: | Mechacode [ Sun Apr 12, 2009 9:32 pm ] |
| Post subject: | Friday Night Projects: Exhaust |
This turned out very nicely. It was a lot of fun saturday night.
|
|
| Author: | Optical Phenomenon [ Mon Apr 13, 2009 8:21 am ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
O yeah CUTOUT FTW. Love the idea |
|
| Author: | Mechacode [ Tue Apr 28, 2009 3:50 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
http://www.youtube.com/watch?v=mazxhMKviak |
|
| Author: | 89D15CRX [ Wed Apr 29, 2009 4:31 am ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
Hey man, is that a 1G FWD downpipe? |
|
| Author: | Mechacode [ Wed Apr 29, 2009 4:01 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
2G awd. Puts the outlet directly into the tunnel. http://cgi.ebay.com/ebaymotors/MEGAN-RA ... ccessories |
|
| Author: | MR HYDE [ Thu Apr 30, 2009 2:35 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
nice job... Question. Where'd you get the red sway bar... 
|
|
| Author: | Mechacode [ Thu Apr 30, 2009 3:07 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
Turbo sway bar I powdercoated at work. 
|
|
| Author: | j2dapo [ Wed May 20, 2009 3:13 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
What does a 1G awd dp do interns of positioning within the tunnel? Quote: 2G awd. Puts the outlet directly into the tunnel.
http://cgi.ebay.com/ebaymotors/MEGAN-RA ... ccessories |
|
| Author: | xxNocturnalxx [ Wed May 20, 2009 4:31 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
hmm. mine will have a 3" o2 housing, i wish the down pipe was 3" all the way through. |
|
| Author: | Mechacode [ Wed May 20, 2009 9:51 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
Quote: What does a 1G awd dp do interns of positioning within the tunnel?
The 1g dp is straight whereas the 2g has the kink. If you're doing the awd swap you'll want the fwd dp to position the exhaust next to the driveshaft. Otherwise I suggest the 2g so be able to tuck the exhaust into the tunnel. |
|
| Author: | xxNocturnalxx [ Thu May 21, 2009 6:47 am ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
I will be doing a cut out very soon as well. Did you get the flanges welded on, or did it come with the down pipe flanges already attached? all the cut outs I found are just bare, I dont have a problem doing the extra work but just would like to know. |
|
| Author: | Mechacode [ Thu May 21, 2009 4:19 pm ] |
| Post subject: | Re: Friday Night Projects: Exhaust |
The Y pipe that came with the cutout had a flange for the cutout but it was welded on at the wrong position so I cut it off and had a new flange welded on in the correct position. The other flange (the one that bolts to the dp) is from RRE I think, the cutout didn't come with it, had to buy it separate ($15 a piece, I bought 2, used 1). The other end that goes to the glasspack is just a slip fit connector with slots cut into it to allow it to actually clamp onto the pipes with exhaust clamps (U bolts). |
|
| Page 1 of 1 | All times are UTC-05:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|