4g61t.org http://www.4g61t.org/forum/ |
|
Expo knuckles/hubs Sold http://www.4g61t.org/forum/viewtopic.php?f=66&t=40848 |
Page 1 of 1 |
Author: | 89Mirageman [ Sat Oct 22, 2016 12:11 pm ] |
Post subject: | Expo knuckles/hubs Sold |
Found a few Expo's while out junkyarding this morning and decided to grab the knuckles. Figure they're getting harder to find and someone would want to upgrade. For those that don't know these allow you to upgrade to the non captive rotor setup. Plus 276mm GVR4 rotors slide right on along with twin piston calipers. Sold Paypal- 89mirageman@live.com free upload upload images |
Author: | 89Mirageman [ Wed Oct 26, 2016 6:32 pm ] |
Post subject: | Re: Expo knuckles/hubs $75 |
No nibbles? These were in big demand not that long ago and I was getting request left and right for them. |
Author: | lancerman [ Wed Oct 26, 2016 6:40 pm ] |
Post subject: | Re: Expo knuckles/hubs $75 |
patience grasshopper |
Author: | 89Mirageman [ Wed Oct 26, 2016 10:32 pm ] |
Post subject: | Re: Expo knuckles/hubs $75 |
I know someone will want them eventually. Just seems weird because this place was loaded with members at one time and some things I posted would sell in minutes. Now it takes a week to get 10 views. |
Author: | Keane [ Wed Oct 26, 2016 10:54 pm ] |
Post subject: | Re: Expo knuckles/hubs $75 |
I know, it seems more are on Facebook which is sad because it speeds the csm knowledge thin and doesn't document things very well |
Author: | 89Mirageman [ Thu Oct 27, 2016 7:58 am ] |
Post subject: | Re: Expo knuckles/hubs $75 |
I actually deleted my FB account about a month or so ago. Just found myself wasting time on there. Don't get me wrong, there's some good stuff on there but most of it is just drama and what my neighbor from 10 years ago ate for dinner I might open a new account in the future but I doubt it. |
Author: | lancerman [ Thu Oct 27, 2016 10:14 am ] |
Post subject: | Re: Expo knuckles/hubs $75 |
I never got into facebook. wife has it and I have perused around more than a few times. never liked the layout. |
Author: | Flying Eagle [ Thu Oct 27, 2016 12:22 pm ] |
Post subject: | Re: Expo knuckles/hubs $75 |
The layout blows chunks for being able to navigate and search anything. Never get what you posted a month ago and try to find again. I hear you guys on all points. |
Author: | coltdriver92 [ Thu Oct 27, 2016 3:05 pm ] |
Post subject: | Re: Expo knuckles/hubs $75 |
When you do this, doesn't it throw you suspension geometry off? Also, when you upgrade to the 276mm GVR4 rotors and twin piston calipers do you need to upgrade your brake booster? I have a peasant base model and I want to actually make it stop decently. |
Author: | 89Mirageman [ Thu Oct 27, 2016 4:32 pm ] |
Post subject: | Re: Expo knuckles/hubs $75 |
You can slot the upper strut mounting hole or use camber plates. I upgraded to the larger elantra booster on my last colt along with an early diamante/3000gt 1" bore M/C. |
Page 1 of 1 | All times are UTC-05:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |