Here are a few pics:
AWD:
FWDs:
| 4g61t.org http://www.4g61t.org/forum/ |
|
| FS: 1g AWD and FWD Scattershields http://www.4g61t.org/forum/viewtopic.php?f=66&t=34746 |
Page 1 of 2 |
| Author: | 89coltgt [ Sat May 14, 2011 1:04 pm ] |
| Post subject: | FS: 1g AWD and FWD Scattershields |
I have one 1g AWD and two 1g FWD Three Speed scattershields, all of them are new, never used or installed. $145 shipped plus paypal fees each. I will try to snap some pics of them later today. |
|
| Author: | 89coltgt [ Mon May 16, 2011 6:35 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
Here are a few pics: AWD: FWDs:
|
|
| Author: | Flying Eagle [ Mon May 16, 2011 6:59 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
I will take 1 fwd scattershield if we know that it will fit the km210 fitted in the c53a. |
|
| Author: | 89coltgt [ Mon May 16, 2011 7:14 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
Tim, they are build for the 1g dsm, is the km132 any larger in size that a dsm trans? I would expect not, but I really don't know. |
|
| Author: | twokss [ Mon May 16, 2011 7:18 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
it should work. i believe only the internals of the trans are different. My f5m33 says Km-210 on the bottom of the case |
|
| Author: | 89coltgt [ Mon May 16, 2011 8:17 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
I was thinking they were physically the same on the outside of the case. There is your answer Tim 
|
|
| Author: | Flying Eagle [ Mon May 16, 2011 8:52 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
I guess they should be if the bell housing and starter/plate locations are the same, being bolted up to the same block dimensions of the 4g6X (non-wide block variety). |
|
| Author: | twokss [ Tue May 17, 2011 5:42 am ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
I know for a fact that the km210 and f5m33 use the same starter plate. Being as I have a fed dsm starter and starter plate in my mirage with the km 210 trans |
|
| Author: | 1japdsm [ Tue May 17, 2011 6:03 am ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
If your using the colt shift linkage you have to cut out a hole in the scattersheild. The linkage needs a passage to go through. I had to do that to my scattersheild to make it work. Just make the measurements and have someone with a plasma cutter do it. |
|
| Author: | Flying Eagle [ Tue May 17, 2011 9:05 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
Ah, fair enough. Good to know for installation time. |
|
| Author: | 89coltgt [ Fri May 20, 2011 12:44 am ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
One fwd shield sold pending payment, only one fwd left guys!! The awd shield is still available as of right now too. |
|
| Author: | 89coltgt [ Sat May 21, 2011 2:11 am ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
One fwd sold, one fwd and awd left fellas. |
|
| Author: | 89coltgt [ Tue May 31, 2011 7:00 pm ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
Up, one awd and one fwd still available. |
|
| Author: | 89coltgt [ Tue Jun 21, 2011 2:11 am ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
bump |
|
| Author: | 89coltgt [ Thu Aug 25, 2011 6:32 am ] |
| Post subject: | Re: FS: 1g AWD and FWD Scattershields |
One fwd left, make reasonable offer. |
|
| Page 1 of 2 | All times are UTC-05:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|