| 4g61t.org http://www.4g61t.org/forum/ |
|
| Need parts, look here! http://www.4g61t.org/forum/viewtopic.php?f=66&t=25357 |
Page 5 of 12 |
| Author: | aaronsbig16g [ Wed May 12, 2010 11:33 pm ] |
| Post subject: | Re: Need parts, look here! |
Looking for a brake booster and the metal filler piece that goes above the front bumper for a 92 colt. |
|
| Author: | vaj_colt [ Sun Jun 06, 2010 3:57 pm ] |
| Post subject: | Re: Need parts, look here! |
You think you can find me a knock sensor and the whole timing belt cover for a 1g thanks. |
|
| Author: | clubman [ Sat Jun 19, 2010 11:19 am ] |
| Post subject: | Re: Need parts, look here! |
im looking for a distributer for a 1994 4g64 2.4l for a eagle summit.I have fryed the coil in the one i have.does anyone know if its possible to change the coil without having to buy a new distributor? |
|
| Author: | moidsm1 [ Tue Aug 17, 2010 12:13 pm ] |
| Post subject: | Re: Need parts, look here! |
I need an early elantra or CSM drivers side L motor mount for my 4G63 Hyundai excel swap. Im using one from a 97-98 elantra and it sits against the body. |
|
| Author: | bluebanana [ Tue Aug 17, 2010 5:00 pm ] |
| Post subject: | Re: Need parts, look here! |
JDM indicators |
|
| Author: | Evotistical [ Tue Aug 17, 2010 5:02 pm ] |
| Post subject: | Re: Need parts, look here! |
Quote: I need an early elantra or CSM drivers side L motor mount for my 4G63 Hyundai excel swap. Im using one from a 97-98 elantra and it sits against the body.
With an 92-95 Elantra mount Your still going to have to make a notch on the driver side engine bay to make room for pulleys and such. When you get your mount, I would make a cut, bang in with a hammer and then re-weld. Have fun! 
|
|
| Author: | 89Mirageman [ Tue Aug 17, 2010 5:27 pm ] |
| Post subject: | Re: Need parts, look here! |
Quote: JDM indicators
try ebay for those, aftermarket ones are just as good.
|
|
| Author: | rono [ Wed Aug 18, 2010 9:45 am ] |
| Post subject: | Re: Need parts, look here! |
Have you seen any ~85-88 420 Mercedes? I have on that is stalling and hardly making any power and there are at least 4 major electronic components that might be the cause. PLMK. |
|
| Author: | moidsm1 [ Thu Aug 19, 2010 9:18 am ] |
| Post subject: | Re: Need parts, look here! |
I wish I lived in Phoenix or San Diego, I would have all the parts I needed too! |
|
| Author: | Legolas337 [ Thu Sep 30, 2010 8:28 pm ] |
| Post subject: | Re: Need parts, look here! |
Looking for a good used 4G15 stock connecting rod. Looks like one of mine is slightly bent, want to put a straight one back in! Thanks |
|
| Author: | 89Mirageman [ Thu Sep 30, 2010 8:59 pm ] |
| Post subject: | Re: Need parts, look here! |
Quote: Looking for a good used 4G15 stock connecting rod. Looks like one of mine is slightly bent, want to put a straight one back in! Thanks
I just gave my 4G15 away a few months ago. 
|
|
| Author: | Legolas337 [ Sun Oct 03, 2010 3:36 pm ] |
| Post subject: | Re: Need parts, look here! |
no prob, they have them on ebay for like $45 shipped. I was hoping someone might have one just laying around. I can wait a little bit here too, I might run up to the yard and see if they can get one for me. Thanks though! |
|
| Author: | dikdiamond [ Mon Nov 22, 2010 9:01 pm ] |
| Post subject: | Re: Need parts, look here! |
I'm looking for a blower motor resistor for my Colt,think you can help me out? |
|
| Author: | knbtsi [ Wed Nov 24, 2010 11:22 am ] |
| Post subject: | Re: Need parts, look here! |
I'm needing GVR4 rear hubs, and e-brake cables for a 89 Colt gt. Would FWD DSM e-brake cables work? |
|
| Author: | CSM Shaun [ Wed Nov 24, 2010 12:05 pm ] |
| Post subject: | Re: Need parts, look here! |
I used FWD DSM cables. Had to use the "L" bracket that holds them on the caliper itself too. |
|
| Page 5 of 12 | All times are UTC-05:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|