4g61t.org http://www.4g61t.org/forum/ |
|
Fastvtgsx awd swap and project page (update- 09/29/2015) http://www.4g61t.org/forum/viewtopic.php?f=64&t=31537 |
Page 5 of 11 |
Author: | dsmcolt969 [ Sun Mar 14, 2010 2:50 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
send me a pm and the the percision with some specs... its close to what im wanting. also wared you pick up that exhaust manifold? |
Author: | fastvtgsx [ Sun Mar 14, 2010 3:49 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
Quote: send me a pm and the the percision with some specs... its close to what im wanting. also wared you pick up that exhaust manifold?
I really don't know the specs on it, maybe their website? I know it's rated for 630hp, journal bearing, full spool around 4500-4800, .63 ar exhaust side. Got the manifold off of ebay, with a lifetime warranty. |
Author: | fastvtgsx [ Sun Mar 14, 2010 7:21 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
Found a few problems/hurdles with using the HY35. The center cartridge needs to be rotated to get the oil fittings at the right angle and the wastegate needs to be modified a little to use internal still. But the biggest problem I've found is the exhaust side hits the block with the manifold I'm using. So I'm going to order a 1/2" spacer to fit that problem. Sucks cause I'll be waiting on parts again. |
Author: | win0857 [ Sun Mar 14, 2010 8:29 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
The exhaust housing hit on my CSM with a Turbonetics manifold(that looks just like your manifold) so I just machined the manifold on a slight angle to kick the turbo out a little. Just a thought, good luck!! |
Author: | fastvtgsx [ Mon Mar 15, 2010 9:32 am ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
That's a pretty good idea actually, but I think I'll still need a spacer, it's leaving about a 1/2 gap at the bottom of my manifold. I have decided to ditch the manifold I have and get a ERL. I don't want the hassle of messing with a spacer, longer studs, denting the water pipe and all the other crap that could go wrong. I think I'll just throw my 16g on until everything I need to run the HY35 comes in. |
Author: | fastvtgsx [ Thu Mar 18, 2010 8:47 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
Well not much to update with... I'm running out of steam quick with this now. Nothing is going right with the build anymore. In the past 3 days I've got the fuel tank half mounted, one side suspension almost done and the shifter mounted. I tried shifting the tranny manually and I could only get it to go into 2nd, 4th and reverse. The tranny is empty of fluid right now but I don't see why it wouldn't go into just those gears. It worked perfectly fine when it was in the talon. If I have to swap the tranny that might be the straw that breaks the camel's back. I guess we'll see when I get it fully back together. I'm hoping it will be by the end of the month but with the way things are going who knows. This car's starting to piss me off. |
Author: | Red Sleeper [ Fri Mar 19, 2010 4:54 am ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
What shift levers did you use on the AWD trans? When i did my AWD swap, i used factory turbo colt shift levers, and put them on the AWD trans. i had every gear. no problem. |
Author: | fastvtgsx [ Fri Mar 19, 2010 7:11 am ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
Quote: What shift levers did you use on the AWD trans? When i did my AWD swap, i used factory turbo colt shift levers, and put them on the AWD trans. i had every gear. no problem.
I'm using all awd stuff, shifter base, cables, brackets and levers. I wasn't even using the cables and shifter when I was going through the gears, I had my hands on the shifter levers themselves. I'm just hoping it's cause of the lack of fluid in it.
|
Author: | Red Sleeper [ Fri Mar 19, 2010 12:28 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
what year trans/linkage? 91-94 AWD trans, has to have 91-94 shifter base and cables.. Also that bracket that holds the cables at the trans, is differnt between the 90 and the 91-94 and between FWD and AWD for those years. |
Author: | 6BoltColt [ Tue Mar 23, 2010 6:16 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
hey man looking good, keep chuggin! |
Author: | dsmcolt969 [ Tue Mar 23, 2010 6:19 pm ] |
Post subject: | Re: Fastvtgsx is taking the awd jump! |
Quote: Quote: send me a pm and the the percision with some specs... its close to what im wanting. also wared you pick up that exhaust manifold?
I really don't know the specs on it, maybe their website? I know it's rated for 630hp, journal bearing, full spool around 4500-4800, .63 ar exhaust side. Got the manifold off of ebay, with a lifetime warranty. |
Page 5 of 11 | All times are UTC-05:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |