4g61t.org

Small update.

Beadblasting and new paint for my KM210


And thanks Mechacode for the first box

The car is stilll looking good! keep it up

_________________
91 colt beater..

Since the bad paint story, the Colt remain in my garage.
I have only buy some parts for the futur rebuild...

First i have home made build a engine stand ( i have find a support for my stickers )


Removed the 4G61T


Ready for a rebuild


This is some parts
4G67 head/ Crower spring & TI retainer/ Light port on intake and exhaust side ( gasket matching ) OEM gasket & ARP / new guide & Ferea seals / 3 angle job/ SS valves/ 3G lifters/ Kyosan Denso 300LPH/ OEM water pump and timing parts


And more
FP race mani/ MAP O2 recirc/ TIAL MVS ( ECU and SAFC for another project car maybe )/ ACL bearing


FP manifold, MAP O2 and new EVO3 turbine housing are at SWAIN TECH (best thermal result in my French head) for a ceramic coating.

I look already for:
EVO3 16G turbo, thanks for your help here: http://www.4g61t.org/forum/viewtopic.php?f=6&t=33399
And bigger PWR water air IC
Yoshifab camber plate
I have received from ECMLink the parts needed for SD and boost control.

CSM family pics
LEFT donor car for this sale http://www.4g61t.org/forum/viewtopic.php?f=66&t=32182 (C58 GTI) Center my daily (C66 4G92) Right my new beater (C53 GTI with US front bumper swap)



Thanks for comments.

Thanks To :
Swain-Tech
Forced Performance
MAPerformance

This car amazes me. The attention to detail will make you feel like you are driving a new car everytime you roll down the road. Hope the wife is supportive!

Thanks Tim

I have no support from my wife , fine for me ...

The O2H come back to MAP, the Tial WG dont fit on it

Update !

Head work this winter


Copper spray for the last head gasket from JNZ


Cam HKS 264/264 and timing installation


Valve cover work


AFCO radiator


Sample pictures of the 4G61T


The shell is still waiting after my paint man

Remy

very nice.. I have the exact same rad I got 2 weeks ago..was also thinking ab out getting this to go with it.. http://www.summitracing.com/parts/AFC-8 ... /?rtype=10

but got almost exact same from from a audi a6 but it is a pusher fan so needs to be mounted in front between ic and rad (if theres room) which will make more space for the large turbo.. cant wait to see pics of it all together.


Steve

_________________
Steve 89 colt 2.3 stroker stock top end. evo3@20 psi 13.489@99.30mph 3/10 2012
On drag radials.auto trans.launching @ 5 psi and no traction thru 2nd.

Thanks !
Nice shroud kit, but i'm not fan.
I prefer an "open" exchange air surface, i need to make custom aluminum bracket for my 14" SPAL.

Update for the last paint job i hope, professionnally done this time
Body + engine bay and doors openings.
I need to wait September for reassembly everything ...

Car's turning out real nice. What kinda rims are you going to put under it?

Thanks.
Stock rims but restored
With YOKOHAMA A048 tires

Paint work in progress





Pictures update next week end after the last paint ...

body paint done
Two base R52 color and two clear coat (both solvanted)
Roof rust traited but i'm lucky about that...




Plastic parts paint in September...

Next step for end of this month for reassembly mechanicals parts.
Thanks again for your support, without your help this project would be a junk car !

Nice work! Is that your X6?