Easiest way to do it without cutting and welding. Note you still need the up/down CSM lever that bolts onto the trans though.
http://www.4g61t.org/forum/viewtopic.ph ... it=shifter
just noticed we bumped an old thread....
| 4g61t.org http://www.4g61t.org/forum/ |
|
| Trans cable help!! http://www.4g61t.org/forum/viewtopic.php?f=57&t=39218 |
Page 1 of 1 |
| Author: | drew24 [ Wed Oct 29, 2014 1:21 pm ] |
| Post subject: | Trans cable help!! |
Ok guys I have been looking around and I can't seem to find what I am actually looking for, I am running an awd transmission out of a 92 talon in my 89 4g63 swaped mirage. I have the factory turbo mirage shifter cables and shifter base. But I am wondering what bracket I need for on the transmission. I have seen where they talk about useing the factory turbo shift levers but I don't remember haveing to run them on my old colt when I had it 6 or 7 years ago. I just know there are a couple diffrent combinations of brackets out there. But I was wondering if some one could let me in on what one would be the correct one I use. Pictures would be helpful to.. Thanks |
|
| Author: | 89Mirageman [ Wed Oct 29, 2014 9:38 pm ] |
| Post subject: | Re: Trans cable help!! |
You need the bracket that bolts to the trans case that holds the cables on, the lever that is bolted on and the one that is welded on. I did a write-up in the archive on how to swap these out. These parts need to come from any 3g csm with a manual trans, turbo or na does not matter. |
|
| Author: | drew24 [ Thu Oct 30, 2014 11:29 am ] |
| Post subject: | Re: Trans cable help!! |
Yea I have seen that but I never had to do that on my old setup, was wondering if anyone else is running the awd factory trans levers and not swapping them out? |
|
| Author: | 89Mirageman [ Thu Oct 30, 2014 2:30 pm ] |
| Post subject: | Re: Trans cable help!! |
Not that I know of. To my knowledge you have to swap the levers to run the stock csm shifter and cables. Were you using a dsm shifter and cables on your last swap? |
|
| Author: | drew24 [ Thu Oct 30, 2014 4:34 pm ] |
| Post subject: | Re: Trans cable help!! |
I don't believe I was, but if I was to run the dsm shifter base and cables do I not need to modify the the shifter arms? |
|
| Author: | win0857 [ Tue Jan 20, 2015 1:07 pm ] |
| Post subject: | Re: Trans cable help!! |
Quote: I don't believe I was, but if I was to run the dsm shifter base and cables do I not need to modify the the shifter arms?
I used the CSM setup and just cut the shift arm of the shifter rods on the original transmission. I then removed the ones on the AWD transmission and welded the CSM parts to the AWD shift rods.Mark |
|
| Author: | UnderPSI [ Tue Jan 20, 2015 3:12 pm ] |
| Post subject: | Re: Trans cable help!! |
Easiest way to do it without cutting and welding. Note you still need the up/down CSM lever that bolts onto the trans though. http://www.4g61t.org/forum/viewtopic.ph ... it=shifter just noticed we bumped an old thread....
|
|
| Author: | 89Mirageman [ Tue Jan 20, 2015 3:50 pm ] |
| Post subject: | Re: Trans cable help!! |
No biggie, I'm sure this info will help someone else who searches in the future. I can't imagine trying to bend that thick shift lever with a pair of visegrips but it looks like it worked out well. It's always nice seeing people doing things differently. |
|
| Page 1 of 1 | All times are UTC-05:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|