4g61t.org
http://www.4g61t.org/forum/

Bolt up cross member
http://www.4g61t.org/forum/viewtopic.php?f=57&t=20777		 Page 7 of 8
Author:  Miragetbo1997cc [ Tue Sep 28, 2010 6:08 pm ]
Post subject:  Re: Bolt up cross member
Not sure
Author:  89Mirageman [ Tue Sep 28, 2010 6:37 pm ]
Post subject:  Re: Bolt up cross member
Quote:
hmmm quick question, would that bolt in to my elantra?


No, the elantra cross member is about 2" longer than the csm ones.
Author:  whe3ls [ Fri Oct 01, 2010 10:34 pm ]
Post subject:  Re: Bolt up cross member
i see. :(
Author:  moidsm1 [ Thu Jan 27, 2011 12:23 am ]
Post subject:  Re: Bolt up cross member
Yea, I tried an elantra xmember for my fwd 4G63t swap and it was too long. I ended up using my stock one
Author:  turbotom20g [ Fri Jan 28, 2011 11:27 pm ]
Post subject:  Re: Bolt up cross member
Quote:
Yea, I tried an elantra xmember for my fwd 4G63t swap and it was too long. I ended up using my stock one
I used the elantra cross member and drilled 2 new holes :twisted:
Author:  moidsm1 [ Wed Feb 23, 2011 1:07 am ]
Post subject:  Re: Bolt up cross member
Damnit tom, You didnt state that on your Cardomain page! I saw you used one but didnt say you modified it! haha, No worries, My car is running fine.
Author:  turbotom20g [ Wed Feb 23, 2011 1:35 am ]
Post subject:  Re: Bolt up cross member
Quote:
Damnit tom, You didnt state that on your Cardomain page! I saw you used one but didnt say you modified it! haha, No worries, My car is running fine.
Sorry buddy, didn't mean to screw you up like that,lol. :cry: But yeah you taught me something as well about the axle problem so we are even then :wink:
Author:  Blackfuse [ Thu Apr 14, 2011 1:28 pm ]
Post subject:  Re:
WAOOOO!!! Bolt up cross member....
I got one of this laying down in my garage with mounts. I bought it from NZ.
Paid bigggg! $$$ to get delivered to Connecticut.
Quote:
Quote:
When looking under the car if you look on the pass sideof the floor there are two bolt hole that have nothing in them.Looks like the same spacing as the bolt holes for the fwd cross member.This is where the back of the crossmember bolts up to.The front bolts up like stock
So, you have made a crossmember to substitute for this factory piece?

Image
Author:  Miragetbo1997cc [ Fri Jun 03, 2011 9:45 am ]
Post subject:  Re: Bolt up cross member
Yeap bolt up. No complaints whatsoever.Tested to 600 hp ,10seconds,1.5 60ft on slicks
Author:  whe3ls [ Fri Jun 10, 2011 8:33 pm ]
Post subject:  Re: Bolt up cross member
i pulled a x member out of a 92 plymouth vista wagon awd auto. there is no rear mount on the block its on the rear of the trans. ill grap a pic later.
Author:  grndsm [ Fri Jun 17, 2011 9:14 am ]
Post subject:  Re: Bolt up cross member
Are you sure this was a '92 and not a '93 made in late '92?

A true '92 vans would have been made between late summer of '91 through early summer of '92. They would also have a 6 bolt motor.
Author:  Miragetbo1997cc [ Tue Jun 21, 2011 12:08 pm ]
Post subject:  Re: Bolt up cross member
Quote:
i pulled a x member out of a 92 plymouth vista wagon awd auto. there is no rear mount on the block its on the rear of the trans. ill grap a pic later.
Ive seen this one. If you get the bracket off the trans, it might bolt up too. My trans from an importer had this bracket but I want something available here all the time. I'm sure auto and 5speed brackets are different.I'll see if I can find the one I had.Its been years.
Author:  whe3ls [ Sat Jun 25, 2011 6:03 am ]
Post subject:  Re: Bolt up cross member
i have xmember with both front and rear mounts
Author:  dsmdizzle [ Sat Jun 25, 2011 12:50 pm ]
Post subject:  Re: Bolt up cross member
Quote:
i pulled a x member out of a 92 plymouth vista wagon awd auto. there is no rear mount on the block its on the rear of the trans. ill grap a pic later.
Look at my awd build thread. I used the awd vista crossmember with success. And I still have a jacking point like before!
Author:  cloead [ Thu Nov 03, 2011 9:21 am ]
Post subject:  Re: Bolt up cross member
Anyone know how to get ahold of this guy? He disappeared :(
Page 7 of 8 All times are UTC-05:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/