4g61t.org http://www.4g61t.org/forum/ |
|
Bolt up cross member http://www.4g61t.org/forum/viewtopic.php?f=57&t=20777 |
Page 5 of 8 |
Author: | phoenixcolt [ Wed Apr 08, 2009 6:16 am ] |
Post subject: | Re: Bolt up cross member |
Great set-up. I am seriously thinking about doing a AWD swap now. |
Author: | aaronsbig16g [ Wed Apr 08, 2009 5:05 pm ] |
Post subject: | Re: Bolt up cross member |
How much do charge for one of these bad boys? |
Author: | Miragetbo1997cc [ Wed May 20, 2009 9:40 am ] |
Post subject: | Re: Bolt up cross member |
Pm for price. |
Author: | Coltsfan [ Thu Jun 18, 2009 11:11 am ] |
Post subject: | Re: Bolt up cross member |
Very nice piece! I have one of the originals (OEM piece) that I haven't installed yet. Has anyone figured out wether or not the rear mount will fit past a stock turbo sway bar? I've held my piece under the car, and it just doesn't look like there's enough room for it to fit behind the differential with the sway bar there. Evo-mirage says it's the same, but I just don't see it. |
Author: | MR HYDE [ Thu Jun 18, 2009 1:24 pm ] |
Post subject: | Re: Bolt up cross member |
The USDM sway bar, is the same is the JDM bar. YES the OEM AWD crossmember will clear the bar. |
Author: | Coltsfan [ Fri Jun 19, 2009 9:07 am ] |
Post subject: | Re: Bolt up cross member |
Quote: The USDM sway bar, is the same is the JDM bar. YES the OEM AWD crossmember will clear the bar.
That's cool. I can't picture it, but I hope it fits. Someday I'll find time to clean it up, paint it, and toss it in there.Thanks |
Author: | MR HYDE [ Wed Jun 24, 2009 8:31 am ] |
Post subject: | Re: Bolt up cross member |
Take another look at your swaybar the next time you are under your car. It has a hump in the design exactly where the t-fer case would reside. You'll be fine, and wont have any clearance issues if you decide to use the 1G AWD tranny and t-fer case Quote: Quote: The USDM sway bar, is the same is the JDM bar. YES the OEM AWD crossmember will clear the bar.
That's cool. I can't picture it, but I hope it fits. Someday I'll find time to clean it up, paint it, and toss it in there.Thanks |
Author: | Miragetbo1997cc [ Fri Jun 26, 2009 9:05 am ] |
Post subject: | Re: Bolt up cross member |
Everything Mr.Hyde said is right on the money. Iit was as if mitsubishi wanted us to do this awd thing |
Author: | LILEVO [ Fri Jun 26, 2009 9:16 am ] |
Post subject: | Re: Bolt up cross member |
Well they did It's just cheaper to have one-car-fits all rather than having a FWD chassis/parts and an AWD chassis/parts. |
Author: | 90mirage [ Mon Jun 29, 2009 4:08 am ] |
Post subject: | Re: Bolt up cross member |
I own a genuine factory 4WD 1990 Mirage that used to be a diesel but now has a 4G63.The 4WD front swaybar is definately different from the FWD bar and the front lower wishbones are also different.You can't use FWD wishbones with a 4WD front swaybar.I tried and it doesn't work as the wishbones are shaped differently and the swaybar links are in a different position on the wishbone. |
Author: | Miragetbo1997cc [ Mon Jun 29, 2009 9:19 am ] |
Post subject: | Re: Bolt up cross member |
Butwe have fwd only and the fwd swaybar allows the transfercase to clear |
Author: | 1slowcsm [ Sun Jul 12, 2009 9:06 am ] |
Post subject: | Re: Bolt up cross member |
I have a crossmember that Miragetbo1997cc made for me. Just installed it yesterday and it fit perfect. We just had to turn it to get the rear mount past the transfer case. It took longer to move the jack stand that was in the way then it did to put the crossmember in. Thanks man!!! |
Author: | Coltsfan [ Sun Jul 12, 2009 9:21 am ] |
Post subject: | Re: Bolt up cross member |
Quote: I own a genuine factory 4WD 1990 Mirage that used to be a diesel but now has a 4G63.The 4WD front swaybar is definately different from the FWD bar and the front lower wishbones are also different.You can't use FWD wishbones with a 4WD front swaybar.I tried and it doesn't work as the wishbones are shaped differently and the swaybar links are in a different position on the wishbone.
The thing I can't see fitting, is the part where the OEM rear engine mount pedestal goes up behind the front differential. There's a tiny space between the differential and the steering rack, and the sway bar goes right through the middle of there. It kinda looks like the rear mount pedestal goes through the middle of there too. I have room for the transfer case I think. |
Author: | 1slowcsm [ Sun Jul 12, 2009 10:47 am ] |
Post subject: | Re: Bolt up cross member |
This setup does not use the stock rear crossmember location. It uses the two bolt holes toward the pass side for rear mounting and motor mount extention goes in from the pass side of transfer case. Also rear engine bracket is inverted to provide clearance past transfer case. Clears everything including sway bar. Hope this helps. |
Author: | Miragetbo1997cc [ Sun Jul 19, 2009 9:00 am ] |
Post subject: | Re: Bolt up cross member |
I'm glad it worked out for your. I knew it would fit perfect. In the picture you can see the bolt holes for the awd crossmember. |
Page 5 of 8 | All times are UTC-05:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |