4g61t.org
http://www.4g61t.org/forum/

Camber plates for a CSM
http://www.4g61t.org/forum/viewtopic.php?f=3&t=30758		 Page 4 of 6
Author:  aaronsbig16g [ Fri Oct 09, 2009 1:32 am ]
Post subject:  Re: Camber plates for a CSM
Quote:
Quote:
just ordered mine.
You got the last set, they will ship in the morning
WIN
Author:  92 TSi AWD [ Mon Oct 12, 2009 8:27 pm ]
Post subject:  Re: Camber plates for a CSM
Has anyone checked to see what kind of camber adjustment these offer? Im considering scrapping my captive rotor setup for a set of GVR4 knuckles and brakes and I want to make sure I can get enough adjustment from these.
Author:  CaptainTonus [ Mon Oct 12, 2009 8:38 pm ]
Post subject:  Re: Camber plates for a CSM
Quote:
Has anyone checked to see what kind of camber adjustment these offer? Im considering scrapping my captive rotor setup for a set of GVR4 knuckles and brakes and I want to make sure I can get enough adjustment from these.
I'm doing that swap very soon on my car, so I'll let you know how it turns out. I predict that I'll have to max them out all the way to get the camber back to normal. Right now I have them set straight up, and I still have some negative camber up front because my car is lowered about 2".
Author:  89Mirageman [ Mon Oct 12, 2009 9:13 pm ]
Post subject:  Re: Camber plates for a CSM
Quote:
Has anyone checked to see what kind of camber adjustment these offer? Im considering scrapping my captive rotor setup for a set of GVR4 knuckles and brakes and I want to make sure I can get enough adjustment from these.

I dug some 92-96 Expo/Summit front knuckles out of my parts stash the other day and noticed that they are very similar to the 3g knuckle. The tie-rod end points down with the nut on the bottom just like the 3g csm's These are 4 x 114.3 and non captive. GVR4 rotors and twin piston calipers bolt right on. These should be a better fit than the GVR4 parts and much easier to find in the yards.
Author:  yoshifab [ Tue Oct 13, 2009 1:05 am ]
Post subject:  Re: Camber plates for a CSM
Here is bowdowns adjustmen with gvr4 hubs...

Image

Plenty of adjustment.
Author:  aaronsbig16g [ Tue Oct 13, 2009 10:49 am ]
Post subject:  Re: Camber plates for a CSM
Just got mine in the mail. They are a really nice piece. I'm so glad I was able to get a set of these, I think that they will work really well. Thanks again Yoishfab for making these up, keep up with the good work. Vehicle Wraps
Author:  Berserko [ Tue Oct 13, 2009 11:43 am ]
Post subject:  Re: Camber plates for a CSM
Quote:
Quote:
Has anyone checked to see what kind of camber adjustment these offer? Im considering scrapping my captive rotor setup for a set of GVR4 knuckles and brakes and I want to make sure I can get enough adjustment from these.

I dug some 92-96 Expo/Summit front knuckles out of my parts stash the other day and noticed that they are very similar to the 3g knuckle. The tie-rod end points down with the nut on the bottom just like the 3g csm's These are 4 x 114.3 and non captive. GVR4 rotors and twin piston calipers bolt right on. These should be a better fit than the GVR4 parts and much easier to find in the yards.

You have to be very careful with thiose knuckles because the steering arm is much shorter than the CSM/GVR4 knuckles
Author:  Devolution [ Tue Oct 13, 2009 10:18 pm ]
Post subject:  Re: Camber plates for a CSM
Quote:
Quote:
Has anyone checked to see what kind of camber adjustment these offer? Im considering scrapping my captive rotor setup for a set of GVR4 knuckles and brakes and I want to make sure I can get enough adjustment from these.

I dug some 92-96 Expo/Summit front knuckles out of my parts stash the other day and noticed that they are very similar to the 3g knuckle. The tie-rod end points down with the nut on the bottom just like the 3g csm's These are 4 x 114.3 and non captive. GVR4 rotors and twin piston calipers bolt right on. These should be a better fit than the GVR4 parts and much easier to find in the yards.

or you could just use 4G knuckles, no positive camber issues with them. GVR4 rotors and calipers bolt right onto them as well. you can even press the hubs out of the Expo spindles and press them into the 4G ones, and keep your 4x114.3 bolt pattern.
Author:  89Mirageman [ Wed Oct 14, 2009 9:07 am ]
Post subject:  Re: Camber plates for a CSM
I have some 4g knuckles with the 4x100 bolt pattern waiting to go on my colt. Just thought this would be a better alternative to the GVR4 knuckles but I had no idea the steering arms were that much shorter.
Author:  MR HYDE [ Wed Oct 14, 2009 11:39 am ]
Post subject:  Recieved mine too
I recieved them in the mail when I was on vacation in Pattaya, Thailand. I just opened the box and they look terrific. Thanks for the parts
Author:  Redline89 [ Wed Dec 02, 2009 4:03 pm ]
Post subject:  Re: Camber plates for a CSM
So the stock turbo model caliper fits on all these? and 4g knuckles work the best, with no modification???

Sorry to reopen this thread. Ive been searching about this upgrade...
Author:  Mechacode [ Wed Dec 02, 2009 11:40 pm ]
Post subject:  Re: Camber plates for a CSM
Which mod are you talking about? This thread was about camber plates.
Author:  Roy [ Sat Dec 05, 2009 2:03 am ]
Post subject:  Re: Camber plates for a CSM
i just saw this, would this camber plate work with 4th gen's also? just asking because it looks like it would work
Author:  Mechacode [ Sat Dec 05, 2009 2:01 pm ]
Post subject:  Re: Camber plates for a CSM
Quote:
i just saw this, would this camber plate work with 4th gen's also? just asking because it looks like it would work

http://cgi.ebay.com/ebaymotors/92-96-La ... ccessories
Author:  Roy [ Thu Dec 10, 2009 5:03 am ]
Post subject:  Re: Camber plates for a CSM
wow ksports, really? no thaks man. single rate springs FTL, i had a set of ksports an didnt like it for the street


about the camber plates, just tryin to help out the seller if he can sell them to the 4th gen guys. i dont even own a 4g mirage
Page 4 of 6 All times are UTC-05:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/